loading

Lesintor - 20+Years Industry experience, Professional plastic crusher manufacturers

Plastic Granulator Screen Size: How It Sets Regrind Quality

Screen aperture is the fastest lever you can pull on regrind quality, and it is usually the last one anyone checks. Change a 10 mm screen to a 6 mm screen and you will cut the coarse fraction in your regrind, raise fines, drop throughput, and change how the material behaves in the feed throat — all within the same machine, same blades, same operator. This guide explains what the screen actually controls, how to match aperture to your downstream process, and how to commission a granulator so the first week of regrind does not become the first month of rejects.

What the screen actually controls

A granulator cuts material between rotating and fixed knives, then holds it against a perforated screen until the particles are small enough to pass. The screen is therefore not a filter bolted on at the end; it is the sizing die of the whole process.

Three things follow from that. First, aperture sets the upper bound of particle size — nothing larger than the hole leaves the chamber. Second, open area sets throughput: a screen with 40 percent open area passes material far faster than one with 25 percent at the same aperture. Third, hole geometry matters. Conical or countersunk holes resist clogging better than straight drilled holes when you are grinding thin-wall parts or film, because material is guided through instead of being smeared across a flat surface.

Operators often blame the knives for inconsistent regrind when the real variable is a worn or blinded screen. A screen that has been hammered flat, has burred edges, or is partly blocked with melted fines will produce a mix of dust and oversize flakes no knife adjustment can fix.

Mapping aperture to particle size and bulk density

Aperture is not particle size. Material exits the screen as irregular flakes whose longest dimension can exceed the hole, because particles pass at an angle. As a rule of thumb, expect the dominant fraction to sit at roughly 0.7 to 1.0 times the aperture, with a tail of fines below 2 mm that grows as aperture shrinks and as knife clearance widens.

That tail is what hurts. Fines below about 1 mm do not fluidise well in a hopper, tend to bridge at the feed throat, and can carry more surface contamination per kilo than larger flakes. Bulk density also falls as particle size drops, which means your volumetric feeder delivers less mass per stroke and your shot weight drifts.

Typical starting points for injection molding scrap:

Aperture Typical use Trade-off
12–16 mm Large purgings, thick sections, shredder output High throughput, coarse regrind, poor feeding on small machines
8–10 mm General runner and sprue regrind Balanced; the usual default
6 mm Precision parts, thin walls, low regrind ratios Lower throughput, more fines, higher energy per kilo
4 mm and below Colour-critical or masterbatch-heavy scrap Slow, heat-sensitive, usually needs a different machine

Treat these as starting points, not standards. The right aperture is the one that produces regrind your machine can actually process at your permitted regrind ratio.

Matching regrind to the next process

The downstream machine, not the granulator, should decide the screen.

Injection molding

Small tonnage machines with 18–25 mm screws are far more sensitive to flake size than a 500-tonne press. If you feed a 6 mm screen's output into a small barrel, you get unstable melting, surging shot weights, and black specks from unmelted flakes. Match aperture to screw diameter: the regrind flake should be comfortably smaller than the flight depth in the feed zone. When in doubt, go one step finer on small machines and one step coarser on large ones.

Extrusion and blow molding

Extrusion dies and screen packs punish oversize flakes and contamination more than they punish fines. A coarser aperture with a well-maintained knife set usually outperforms a fine screen here, because throughput matters and the melt filter catches the rest.

Where colour is critical — masterbatch blending, natural resin, transparent parts — fines are the enemy because they disperse pigment differently from the virgin pellet. In those cases a finer screen plus a dedusting step beats a coarse screen alone.

Knife geometry, gap and rotor speed

Screen size cannot compensate for a badly set cutting chamber. Bed knife clearance is the variable that most often gets ignored: as clearance opens from a correct 0.1–0.2 mm to 0.5 mm or more, the machine stops cutting and starts tearing. Tearing produces dust, heat, and long stringers that wrap the rotor.

Rotor speed has a similar effect. High speed gives throughput and a more uniform particle shape but raises temperature, which matters for PVC, PET, and any heat-sensitive compound. Low speed protects the material but produces flatter, more angular flakes that pack badly.

A practical check: after 20 minutes of running, open the chamber and look at the screen. A healthy setup shows clean holes, uniformly sized flakes, and no melted film on the screen surface. Melted film means the material is being rubbed rather than cut — check knife gap before you touch the screen.

The throughput-versus-quality trade-off

Buyers frequently ask for one granulator that handles purgings and also produces fine, colour-critical regrind. Those are different machines, and asking one unit to do both produces a compromise that is mediocre at each.

The honest trade-off is measurable. Halving aperture typically costs 20–40 percent of throughput on the same rotor, raises specific energy per kilo, and increases fines. If your scrap volume is small and your quality requirement is high, accept the throughput loss. If you are recycling bulky purgings at volume, run a coarse screen and accept that this regrind goes back into non-critical parts.

Measure the trade-off rather than assuming it. Run the same scrap lot through two screens, weigh the output over a fixed ten-minute window, and sieve a one-kilo sample from each. Record kilos per hour, amps drawn, and the share of particles below 1 mm. Most plants find the coarse screen runs 25–35 percent faster with roughly half the fines share of the fine screen — which is the number to put in front of whoever is asking for finer regrind.

The alternative — and usually the better answer — is two-stage reduction: a shredder to bring bulky material down, then a granulator with the aperture you actually need. LESINTOR builds both stages, which is why the double-shaft shredder and the granulator range are normally specified together rather than separately.

A six-point commissioning checklist

Use this when a granulator is installed or when regrind quality suddenly changes:

  1. Verify aperture against the drawing. Screens get swapped between machines. Measure the holes, do not trust the label.
  2. Check open area and hole condition. Blinded or burred holes behave like a smaller, worse screen.
  3. Set bed knife clearance to 0.1–0.2 mm and re-check after the first hour of running.
  4. Confirm rotor knife torque to the manufacturer's figure; loose knives produce oversize flakes and vibration.
  5. Run a 10 kg sample and sieve it. Record the share above 8 mm and below 1 mm. That baseline is what you compare against next quarter.
  6. Check regrind temperature at the outlet. If it is warm to the touch, you are generating fines and risking degradation.

Keep those six numbers in the machine log. Most "the granulator got worse" complaints are one of them drifting.

FAQ

Does a smaller screen always give better regrind?

No. It gives smaller regrind, which is not the same thing. Below a certain size you gain fines, lose throughput, and raise melt temperature. The correct aperture is the coarsest one that still feeds your downstream machine reliably.

How often should granulator screens be replaced?

Inspect monthly and replace when holes are distorted, edges are burred, or open area is visibly reduced by embedded material. A screen is a wear part, not a permanent component.

Can I run regrind at 100 percent?

Only on parts where the specification allows it. Most injection molding applications cap regrind between 10 and 30 percent because flake size, bulk density, and thermal history differ from virgin pellet. The granulator determines whether that cap is comfortable or painful.

Why does my regrind have long stringers?

Stringers mean the material is being torn rather than cut. Check bed knife clearance first, then rotor knife sharpness, then whether the screen is seating flat against the chamber.

Need to match a granulator to your scrap and your machine? Send LESINTOR your part weight, wall thickness, scrap volume per shift, and the machine you will feed — we will recommend aperture, rotor type, and whether a two-stage shredder-plus-granulator setup is the better fit.

prev
Oil-Type Mold Temperature Controller: The Complete High-Temperature Heating Guide
recommended for you
Get in touch with us
Tel
+86 15851665433
sales6@lesintormachine.com
+1 628 488 4101
Wuqiao Vilage, Lili Town, Wujiang District, Suzhou City, Jiangsu Province, China
Leave A Message And We Will Contact You
Let's Have A Chat
Copyright © 2026 LESINTOR | Sitemap |  privacy policy
Contact us
phone
email
wechat
whatsapp
Contact customer service
Contact us
phone
email
wechat
whatsapp
cancel
Customer service