loading

Lesintor - 20+Years Industry experience, Professional plastic crusher manufacturers

Powerful Crusher LXT-PC: 50 to 1500 kg/h Explained

Power, blade count and screen aperture: what actually moves throughput

One crusher range covers 50 to 1500 kg/h. Here is what actually changes across all nine models: power, blade count, rotor size, screen and feed opening.

A 30-fold spread in throughput inside one series is not marketing padding — it is the difference between a machine that sits beside a 90-ton press and one that eats pallets at the end of a recycling line. The LXT-PC range runs from the PC180 at 50–100 kg/h to the PC1000 at 750–1500 kg/h, and every step between them changes four things at once: motor power, rotor diameter, blade count and feed opening. Understanding which of those four you are actually buying is the difference between a correctly sized machine and one that runs at half its rated output for the next five years.

What the model digits do and do not tell you

It is tempting to read PC400 as "400 mm something". Resist that. Across the range, the digits step with capacity, but no single dimension maps to them: the PC400 runs 250–450 kg/h on a 7.5 kW motor with a 250 mm rotor and a 310 mm rotation diameter, while the PC600 delivers 450–800 kg/h at 15 kW with a 350 mm rotor. The number is a size class, not a measurement.

What the datasheet does give you, model by model, is the full set of parameters that decide whether the machine fits your scrap. That table is the useful part, and it is worth reading in columns rather than rows. Two models can share a motor size and still differ in feed opening by 200 mm, which is the dimension that decides whether a particular crate fits at all. Two models can share a motor size and still differ in feed opening by 200 mm, which is the dimension that decides whether a particular crate fits at all.

The throughput table, read properly

Model Capacity (kg/h) Power (kW) Rotary blades Fixed blades Rotor Ø (mm) Feed opening (mm)
PC180 50–100 2.2 9 2 148 150×200
PC250 150–200 4 6 2 225 200×250
PC300 200–300 5.5 9 2 240 220×320
PC400 250–450 7.5 12 2 250 250×420
PC500 400–700 11 15 2 310 310×500
PC600 450–800 15 18 2 350 330×620
PC700 500–1000 22 21 4 400 420×720
PC800 650–1300 30 24 4 400 500×820
PC1000 750–1500 37 30 4 400 550×1020

Two things stand out once the table is laid out this way. First, power scales roughly linearly with capacity — 2.2 kW at the bottom, 37 kW at the top — which is the honest signal of what the machine can absorb. Second, rotor diameter stops growing at 400 mm from the PC700 upward, while blade count and feed opening keep climbing. That is the design telling you where the limit sits: beyond about 700 kg/h, throughput comes from a wider working face and more cuts per revolution, not from a bigger swing.

Shaft speed runs 480–650 rpm across the range, with the smaller models turning faster (520–617 rpm) and the largest settling at 480 rpm. Slower, heavier rotors trade impact energy for torque, which is what you want when the feed is dense rather than brittle.

The four variables that set real output

Rated capacity assumes a material, a feed method and a screen. Change any of the three and the number moves.

Screen aperture. The PC range ships with 6–12 mm screens. A 6 mm screen on a PC500 will not deliver 400–700 kg/h on thin-wall polypropylene — the machine spends its time re-cutting material that is already small enough. A 12 mm screen will hit the top of the range and hand you granules that are too coarse for a small injection shot. Screen choice is a quality decision first and a throughput decision second.

Blade count and rotor geometry. Nine blades on a 148 mm rotor and thirty blades on a 400 mm rotor are doing different jobs. More blades per revolution means more cuts per kilo, which produces a tighter particle distribution and consumes more energy per tonne. Fewer, heavier blades grab bulky material more aggressively and tolerate contamination better.

Feed opening. This is the specification people skip and then regret. A 150×200 mm opening will not accept a moulded housing no matter what the capacity column says. If your scrap includes hollow parts, crates or thick sections, the feed opening — not the throughput — decides the model.

Feed method. Gravity feeding from a bin, conveyor feeding, or robot-fed sprue returns each present material to the rotor differently. Continuous, metered feed gets closest to the rated figure. Slug feeding — dumping a full bin at once — spikes current draw and trips overload protection long before the hourly average is reached.

Matching the model to your scrap, by case

Your scrap Start here Why
Sprue and runner from one press PC180–PC250 Throughput is small and intermittent; a bigger rotor wastes energy at part load
Thin-wall packaging, crates PC400–PC600 Bulk density is low, so volumetric throughput matters more than tonnage
Thick sections, glass-filled parts PC600–PC800 Needs torque and a heavy rotor; expect faster blade wear
Mixed plant regrind, centralised PC800–PC1000 Wide feed opening plus a conveyor keeps the rotor fed evenly
Purgings and lumps Not this range Go to a shredder first; a granulator will stall or bounce

Use the table as a starting bracket, then confirm the choice against the feed opening. The first and last rows are the ones that most often surprise buyers.

Use the table as a starting bracket, then confirm the choice against the feed opening. The first and last rows are the ones that most often surprise buyers.

The last row matters. A powerful crusher is a granulator: it cuts material small against a screen. It is not a primary shredder. Lumps and purgings belong in a single or double shaft machine, with the granulator downstream.

What the datasheet cannot tell you

Rated capacity is measured on a reference material, usually a clean, rigid regrind at a stated bulk density. Your scrap will differ. Three checks close the gap:

  1. Weigh a representative sample. Fill a 20-litre bucket with your actual scrap and weigh it. Bulk density below about 100 kg/m³ means the volumetric limit binds before the weight limit does.
  2. Run your own material for ten minutes. Measure kilos out, not kilos in. Current draw on the nameplate amps tells you whether the motor is working or idling.
  3. Ask what material the rating was measured on. If the answer is generic regrind and yours is film or foam, discount the figure before comparing models.
  4. Check the granule you actually need. Sieve a sample. If more than a small fraction passes 1 mm, you are making dust, and dust is the fraction that causes feeding problems and burn marks downstream.

Maintenance that protects the rating

Three items keep a granulator at its rated output, and all three are cheap until they are ignored. Blade gap, normally set at 0.1–0.2 mm between rotating and fixed knives, widens as edges wear; a gap that has drifted to 0.5 mm turns a cutting action into a tearing action, raising fines and lowering throughput. Screen condition matters as much — a screen that has been hammered flat or partly blinded by melted fines restricts flow regardless of rotor speed. Log the three readings monthly — blade gap, screen condition, belt tension — and the machine holds its rating for years. Skip them and the first symptom is usually a customer complaint about flow lines, not a machine fault.

Log the three readings monthly — blade gap, screen condition, belt tension — and the machine holds its rating for years. Skip them and the first symptom is usually a customer complaint about flow lines, not a machine fault.

And the belt or coupling tension, checked monthly, is the difference between 480 rpm at the rotor and 480 rpm at the motor.

FAQ

Can one crusher handle both thin film and thick parts? Not well. Film needs a different knife geometry and a much larger feed throat relative to throughput; thick parts need torque. Trying to cover both usually means compromising on both.

Is a bigger model always safer? No. A PC1000 running at 200 kg/h draws more idle current, takes more floor space and produces a coarser granule than a correctly sized PC400. Oversizing is a common and expensive mistake.

How often should blades be sharpened? It depends on filler content and wall thickness, but the signal is granule quality and current draw, not the calendar. Glass-filled material can dull an edge in weeks; unfilled PE can run for many months.

Does screen size affect motor load? Yes. A finer screen holds material in the chamber longer, so the same feed rate draws more amps. If you move from 12 mm to 6 mm, expect to reduce feed rate or accept a higher current reading.

For plants specifying a granulator, the practical route is to fix the feed opening from the largest part you will ever put in, then choose the screen from the granule your process needs, and only then read the capacity column. Lesintor's LXT-PC series covers that decision across nine models from 2.2 kW to 37 kW, with claw or flat knife configurations and customised screen mesh.

prev
Oil-Type Mold Temperature Controller: The Complete High-Temperature Heating Guide
Claw Knife vs Flat Knife: Choosing Crusher Blades
next
recommended for you
Get in touch with us
Tel
+86 15851665433
sales6@lesintormachine.com
+1 628 488 4101
Wuqiao Vilage, Lili Town, Wujiang District, Suzhou City, Jiangsu Province, China
Leave A Message And We Will Contact You
Let's Have A Chat
Copyright © 2026 LESINTOR | Sitemap |  privacy policy
Contact us
phone
email
wechat
whatsapp
Contact customer service
Contact us
phone
email
wechat
whatsapp
cancel
Customer service