loading

Lesintor - 20+Years Industry experience, Professional plastic crusher manufacturers

Three-in-One Dryer LXT-CDY: Reaching -40°C Dew Point

Hot air dries the surface; only dry air pulls water out of the pellet
×
Three-in-One Dryer LXT-CDY: Reaching -40°C Dew Point

Two dryers can both read 120℃ on the display and produce completely different parts. Temperature tells you how hard the machine is working; dew point tells you whether the air it is blowing can still absorb water. For hygroscopic resins — PA, PC, PET, PBT, LCP — the second number decides quality, and it is the one most often missing from a quotation. The LXT-CDY range is built around it: −40 to −50℃ dew point, drying capacity from 25 to 1000 kg, hoppers from 40 to 1500 L.

Dew point is the number that matters

Dew point is the temperature at which the air in the hopper would start to condense moisture. A low dew point means very little water vapour is present, which means the air still has capacity to pick up water from the pellet. A high dew point means the air is already loaded, and blowing it harder only heats the pellet.

That is why the same 120℃ setpoint behaves differently in February and in the monsoon. Ambient air carries different moisture, so a dryer that simply heats plant air delivers a different result in different weather. A dehumidifying dryer removes that variable by drying the process air first, then heating it.

The numbers here are not a marketing range: −40 to −50℃ is roughly two orders of magnitude less moisture than ambient air holds on a humid day. That gap is what makes the drying of engineering resins repeatable from batch to batch.

Surface water versus absorbed water

The distinction is easy to state and expensive to ignore.

Surface moisture sits on the outside of the pellet and comes off with modest heat and time. Absorbed moisture is inside the polymer structure, held by the same polarity that makes the resin hygroscopic in the first place. Heating drives it out only if the surrounding air is dry enough to accept it — otherwise the system reaches equilibrium with the pellet still wet.

This is why the handbook temperatures for ordinary hopper drying look modest: PE and PP at around 80℃ for two hours, PS and ABS at around 82℃, PA and PC at 120℃ for two to three hours. For polyolefins that is genuinely enough, because there is almost no absorbed water to remove. For PA and PC it is enough only if the air is dry. Blow humid air at 120℃ and the pellet comes out hot and still wet, and the symptom appears downstream as silver streaking, bubbles or a drop in impact strength — never as a dryer alarm.

A hopper dryer, in short, removes surface water. A dehumidifying dryer removes absorbed water. The CDY range is specified for PA, PC, LCP, PET and PBT for exactly that reason.

What "three in one" means in practice

The name describes three functions sharing one frame and one control: dehumidifying, drying and conveying.

Dehumidifying. A desiccant section dries the process air to the target dew point before it enters the hopper. Airflow across the range runs 50 to 1000 m³/h, matched to hopper size — too little airflow and the hopper stratifies, with dry pellets at the inlet and wet ones at the far end.

Drying. A heater raises that dry air to the resin's drying temperature, and the hopper holds the residence time. Hopper volume from 40 to 1500 L sets how much material is in residence at once, which is the real constraint on throughput: drying is a time-at-temperature-and-dew-point process, not an instantaneous one.

Conveying. A vacuum loader on the same frame fills the hopper on demand. Combining it with the dryer is not cosmetic — it removes a manual refill step that otherwise opens the hopper to ambient air every hour, which is precisely what a dew point target cannot tolerate.

The practical benefit is footprint and consistency. One machine, one set of settings, one place to check.

Three-in-One Dryer LXT-CDY: Reaching -40°C Dew Point 1

The CDY range in numbers

Item LXT-CDY25KG – CDY1000KG
Dew point −40 to −50℃
Drying capacity 25 – 1000 kg
Hopper volume 40 – 1500 L
Dehumidified airflow 50 – 1000 m³/h
Drying heater power 0.4 – 5.5 kW
Suited resins PA, PC, LCP, PET, PBT

Read the range from the hopper volume and the airflow together. Drying capacity in kilos is a derived figure that assumes a resin, a starting moisture and a residence time; the hopper and the airflow are the physical facts that decide whether your process can hit its cycle. A 25 kg unit and a 1000 kg unit are not the same machine scaled up — they serve different production rates, and the airflow figure is what tells you how quickly the hopper recovers after a refill.

The heater power looks small next to the drying capacity, and that is correct: the energy in this process goes into regenerating the desiccant and moving air, not into brute heating. A dryer specified by heater kilowatts is being specified on the wrong variable.

Checking the dew point you paid for

A dew point display is an instrument, and instruments drift. Three checks keep the number honest.

Give it time to stabilise. Dew point readings settle after the desiccant section reaches its working cycle, not at switch-on. Reading the display two minutes after start-up tells you about the ambient air, not the machine.

Measure at the hopper inlet, not at the panel. The point of interest is the air entering the material. A sensor upstream of a long, leaky hose can read dry while the hopper sees humid air.

Check the seals when the number drifts. A dew point that gradually rises over months is usually ingress — a worn hopper lid gasket, a loose hose clamp, a loader flap that does not seat. The desiccant is blamed far more often than it is at fault.

For PET and sensitive optical grades, log the reading with the batch. When a streaking complaint appears, the log answers in a minute whether the dryer or the resin was responsible.

Where the machine does not pay

A dehumidifying dryer is not the default for every hopper. For PE, PP, PS and ABS running ordinary cosmetic parts, a conventional hopper dryer at the handbook temperature is sufficient, and the extra capital buys nothing. The exception is a plant that runs polyolefins and engineering resins on the same floor and wants one drying standard — there the CDY earns its place on consistency rather than on any single job. Nor is it a substitute for dry storage: a sealed bag of pre-dried resin opened into a humid room picks moisture up again, and no dryer mounted on the machine can undo a weekend of that.

The other case where it does not pay is a machine with no residence time. If the hopper is refilled every twenty minutes from a wet bin, the material never spends long enough at dew point to dry, and the answer is a larger hopper or a central drying system, not a bigger dryer.

FAQ

Can I reach −40℃ dew point with a refrigerated dryer instead?

Refrigerated drying typically bottoms out well above that. A desiccant-based dehumidifying dryer is what reaches −40℃ and below, which is why engineering resins are specified with one.

Does the three-in-one unit dry and convey at the same time?

Yes — the loader refills the hopper on demand while drying continues, which is the point of combining them. Refilling by hand opens the hopper to ambient air and works against the dew point target.

How long does PA need at −40℃ dew point?

Residence time depends on grade, wall thickness and starting moisture; the handbook figures for PA sit around 120℃ for about two hours, and that assumes dry air. Use the resin supplier's drying curve and confirm with a moisture reading on the finished part.

Is a lower dew point always better?

No. Below the resin's requirement you spend regeneration energy for no quality gain. Match the dew point to the polymer — −40℃ covers the hygroscopic engineering grades; optical PET is where the lower end of the range matters.

Lesintor builds the LXT-CDY three-in-one range from 25 kg to 1000 kg drying capacity with 40 to 1500 L hoppers, −40 to −50℃ dew point and integrated conveying, alongside conventional LXT-DY hopper dryers for polyolefins that only need surface moisture removed.

prev
Chiller Sizing: kW, kcal/h and What the Datasheet Hides
recommended for you
Get in touch with us
Tel
+86 15851665433
sales6@lesintormachine.com
+1 628 488 4101
Wuqiao Vilage, Lili Town, Wujiang District, Suzhou City, Jiangsu Province, China
Leave A Message And We Will Contact You
Let's Have A Chat
Copyright © 2026 LESINTOR | Sitemap |  privacy policy
Contact us
phone
email
wechat
whatsapp
Contact customer service
Contact us
phone
email
wechat
whatsapp
cancel
Customer service